- 您现在的位置：买卖IC网 > Sheet目录481 > MTP2P50E (ON Semiconductor)MOSFET P-CH 500V 2A TO-220AB
MTP2P50E
POWER MOSFET SWITCHING
Switching behavior is most easily modeled and predicted
by recognizing that the power MOSFET is charge
controlled. The lengths of various switching intervals ( D t)
are determined by how fast the FET input capacitance can
be charged by current from the generator.
The published capacitance data is difficult to use for
calculating rise and fall because drain ? gate capacitance
varies greatly with applied voltage. Accordingly, gate
charge data is used. In most cases, a satisfactory estimate of
average input current (I G(AV) ) can be made from a
rudimentary analysis of the drive circuit so that
t = Q/I G(AV)
During the rise and fall time interval when switching a
resistive load, V GS remains virtually constant at a level
known as the plateau voltage, V SGP . Therefore, rise and fall
times may be approximated by the following:
t r = Q 2 x R G /(V GG ? V GSP )
t f = Q 2 x R G /V GSP
where
V GG = the gate drive voltage, which varies from zero to V GG
R G = the gate drive resistance
and Q 2 and V GSP are read from the gate charge curve.
During the turn ? on and turn ? off delay times, gate current is
not constant. The simplest calculation uses appropriate
values from the capacitance curves in a standard equation for
voltage change in an RC network. The equations are:
t d(on) = R G C iss In [V GG /(V GG ? V GSP )]
t d(off) = R G C iss In (V GG /V GSP )
The capacitance (C iss ) is read from the capacitance curve at
a voltage corresponding to the off ? state condition when
calculating t d(on) and is read at a voltage corresponding to the
on ? state when calculating t d(off) .
At high switching speeds, parasitic circuit elements
complicate the analysis. The inductance of the MOSFET
source lead, inside the package and in the circuit wiring
which is common to both the drain and gate current paths,
produces a voltage at the source which reduces the gate drive
current. The voltage is determined by Ldi/dt, but since di/dt
is a function of drain current, the mathematical solution is
complex. The MOSFET output capacitance also
complicates the mathematics. And finally, MOSFETs have
finite internal gate resistance which effectively adds to the
resistance of the driving source, but the internal resistance
is difficult to measure and, consequently, is not specified.
The resistive switching time variation versus gate
resistance (Figure 9) shows how typical switching
performance is affected by the parasitic circuit elements. If
the parasitics were not present, the slope of the curves would
maintain a value of unity regardless of the switching speed.
The circuit used to obtain the data is constructed to minimize
common inductance in the drain and gate circuit loops and
is believed readily achievable with board mounted
components. Most power electronic loads are inductive; the
data in the figure is taken with a resistive load, which
approximates an optimally snubbed inductive load. Power
MOSFETs may be safely operated into an inductive load;
however, snubbing reduces switching losses.
1800
1600
1400
V DS = 0 V
C iss
V GS = 0 V
T J = 25 ° C
1000
V GS = 0 V
T J = 25 ° C
C iss
1200
100
1000
800
C iss
C oss
600
C rss
10
C rss
400
200
C rss
C oss
0
10
5
0
5
10
15
20
25
1
10
100
1000
V GS
V DS
V DS , DRAIN-TO-SOURCE VOLTAGE (VOLTS)
GATE-TO-SOURCE OR DRAIN-TO-SOURCE VOLTAGE (VOLTS)
Figure 7a. Capacitance Variation
http://onsemi.com
4
Figure 7b. High Voltage Capacitance
Variation
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MTP3055VL
MOSFET N-CH 60V 12A TO-220AB
MTP3055VL
MOSFET N-CH 60V 12A TO-220
MTP3055V
MOSFET N-CH 60V 12A TO-220AB
MTP36N06V
MOSFET N-CH 60V 32A TO-220AB
MTP50P03HDL
MOSFET P-CH 30V 50A TO-220AB
MTPD1346-010
PIN DIODE 1300NM FLAT 2.8MM TO46
MTPD1346-030
PIN DIODE 1300NM FLAT 2.8MM TO46
MTPD1346-100
PIN DIODE 1300NM FLAT 2.8MM TO46
相关代理商/技术参数
MTP2P50E_10
制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Power MOSFET 2 Amps, 500 Volts
MTP2P50EG
功能描述:MOSFET 500V 2A P-Channel RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
MTP2S-E10-C
功能描述:电缆束带 Multiple Tie Plate 2 Bund, M-S ties #10 RoHS:否 制造商:Phoenix Contact 产品:Cable Tie Mounts 类型:Adhesive 颜色:Black 材料:Acrylonitrile Butadiene Styrene (ABS) 长度:19 mm 宽度:19 mm 抗拉强度:
MTP2S-E10-C39
功能描述:电缆束带 Mutiple Tie Plate, 2 Bundle, M-S Ties, # RoHS:否 制造商:Phoenix Contact 产品:Cable Tie Mounts 类型:Adhesive 颜色:Black 材料:Acrylonitrile Butadiene Styrene (ABS) 长度:19 mm 宽度:19 mm 抗拉强度:
MTP2S-E6-C
功能描述:电缆束带 Mutiple Tie Plate, 2 Bundle, M-S Ties, # RoHS:否 制造商:Phoenix Contact 产品:Cable Tie Mounts 类型:Adhesive 颜色:Black 材料:Acrylonitrile Butadiene Styrene (ABS) 长度:19 mm 宽度:19 mm 抗拉强度:
MTP3
制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Three Phase Bridge (Power Module) 45 A to 100 A
MTP30
制造商:NELLSEMI 制造商全称:Nell Semiconductor Co., Ltd 功能描述:Glass Passivated Three-Phase Bridge Rectifier, 30A
MTP3001N3
制造商:CYSTEKEC 制造商全称:Cystech Electonics Corp. 功能描述:P-CHANNEL ENHANCEMENT MODE POWER MOSFET